1927 model 9 Questions

Started by Russ, October 05, 2026, 08:51:20 AM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

wessex_man

Hi Russ no idea where you could get one. Quite a few of the hand pumps of the era have this valve fitted to stop the oil blowing back. Anyway it shouldn't be to hard to make what's missing. Here's some pics and dimensions to help you. RE the disk If it were me I'd make a tool to stamp/punch it out. As is often the case it takes more time to make the tooling than the actual item it's self. I've assumed you have the correct fitting on the pump just missing the bits inside. To check for the correct operation take the pump off clean it and simply blow and suck down the oil feed to confirm operation.

Russ

thanks for the reply I definitely don't have that clack valve in the end of my oil feed pipe that goes to the 2 way valve any idea where I might be able to get one.......I seem to remember Lloyd Hansa (Rob Lloyd) used to make and sell these but since his passing I think they've closed down.....I could possibly have a stab at making the little brass holder if I had some rough measurements

wessex_man

#10
Hi Russ, The non return valve I am referring to is located in the bottom union connection not spring and ball bearing at the sight glass.
If you are not getting any oil from the Best & Lloyd pump to the sight glass you are probably pumping in air from somewhere. The sight glass is a favourite leaky spot.  Remember it has quite a way to go from the oil tank to the pump where it's regulated back up to the sight-glass reservoir then to the engine. It can take a while to get to the sight gauge.

Yes there an engine breather in the cam timing casing  but remember the engine will also breathe up the push rod adjusters.

Russ

thanks for the reply.....er......not sure I understand but let's have a go......there's only one crankcase breather which pokes into the Timing side casing right so what stops the crankcase pressure from blowing up the oil feed pipe back up through the 2 way valve and into the sight glass? inside the tank mounted oil pump / sight glass arrangement there is a ball bearing and a small spring this as far as I understand is the non return valve that shuts off the feed from the hand pump into the sight glass.....I guess I'll have to work through methodically to see what it might be that's causing the oil to not drip into the sight glass starting with the pump

WhatsApp Image 2026-11-04 at 09.02.22.jpg


wessex_man

#8
Hi Russ no the non return valve is located on the pump. There's a clacker valve inside the union at the bottom of the feed pipe. Think it's a light spring and steel diaphragm from memory. The engine sucks the oil in on the appropriate stroke then the valve closes to prevent oil from blowing back on the other.   

I think you will find the 90's oiling system is different than a 9's.  and had a direct feed from the oil tank to the crankcases cable operated. I think this was a backup policy should the mechanical pump fail.

Russ

Quote from: wessex_man on October 19, 2026, 08:17:34 PMHi Russ
The main oil feed to the engine is clamped in place and shouldn't be loose when the engine bolts are tightened up. So no nut required.

The oil connection on  timing side is an addition. Suggesting a direct hand pump feed was at some stage used. What type of tank and associated oil pump is fitted? As the correct hand pump and combined sight gauge was used in 1927 only.

Re how it's plumbed. There is a main feed from the oil tank which goes to the best Lloyd pump which is pumped up to a the sight gauge . In addition a hand pump also can be use to directly pump in to the sight gauge. From the sight reservoir a two way position tap is fitted which in the usual position feed the oil to 'the spray nozzle' which feeds the big end. In The taps other position it feeds the gear box.

In 1929 onwards Marston's directly fed the mains.

End float between 10-12 thou see 'Radco' page 85 worth buying the book, if you haven't got one.

The bronze inserts extend the full length and are an interference press fit in the crank case. Complete swine to remove. If too slack simpler to machine oversize push rod adjusters and ream to suit.


is there supposed to be something inside the body of the oil Spray nozzle I'm sure I read somewhere it had some sort of one way arrangement inside otherwise what stops back pressure reversing backup the main oil line from the tank mounted drip feeder bowl and why is the main body of the nozzle much larger......any thoughts

Thomas

1946 BSA C11
1937 Sunbeam Model 9
... and a scratched Hyundai
(MSCR member)

Russ


Thomas

Hi Colin, I just see that you use your email address as the avatar name. I recommend not to do that. It is not protected inside the forum and every external person/machine can see it. Internet machines (crawlers) can use it for spam and phishing attacks. See also https://www.marston-sunbeam.org/sunbeamForum/index.php?topic=1368.0
Cheers, Thomas
1946 BSA C11
1937 Sunbeam Model 9
... and a scratched Hyundai
(MSCR member)

Russ

#3
Hi there
thanks for the reply....my '27 M9 is exactly as your photo with the 2 way valve either feeding the engine or the gearbox....the spare engine I'm rebuilding which is the photo in the first post has the additional oil feed in the timing case which from what I've seen is something the M90 had......as you know it feeds directly into the cam side timing case I was just wondering if it would be a good idea to take the gear box feed and re-route it to the cam timing case feed instead or feed the actual engine feed here instead of the front of the crankcase it might save munching through cam profiles........thoughts......maybe on reflection the later might not be such a good idea as oil might get above the level of the crank breather wouldn't want oil blowing out of there when it opens.....I guess you could make the tube for the breather inside the casing longer and more upturned.....food for thought.....I'll have to look into how the M90 is plumbed......pictures of that would be useful......I have Radcos Workshop manual

wessex_man

#2
Hi Russ
The main oil feed to the engine is clamped in place and shouldn't be loose when the engine bolts are tightened up. So no nut required.

The oil connection on  timing side is an addition. Suggesting a direct hand pump feed was at some stage used. What type of tank and associated oil pump is fitted? As the correct hand pump and combined sight gauge was used in 1927 only.

Re how it's plumbed. There is a main feed from the oil tank which goes to the best Lloyd pump which is pumped up to a the sight gauge . In addition a hand pump also can be use to directly pump in to the sight gauge. From the sight reservoir a two way position tap is fitted which in the usual position feed the oil to 'the spray nozzle' which feeds the big end. In The taps other position it feeds the gear box.

In 1929 onwards Marston's directly fed the mains.

End float between 10-12 thou see 'Radco' page 85 worth buying the book, if you haven't got one.

The bronze inserts extend the full length and are an interference press fit in the crank case. Complete swine to remove. If too slack simpler to machine oversize push rod adjusters and ream to suit.


Russ

Hi chaps
I have some questions about a 1927 model 9 that I'm hoping you knowledgeable chaps might have the answers to.......so the crankcase oil spray nozzle how is it held in place and should it have a fibre washer to seal it........the nozzle tube end has 2 flats one either side (see photo) should there be some kind of retaining nut or washer as the fit as it is is quite loose.......it also has an oil connection into the timing side crankcase that feeds directly into the cam casing how is this piped up......forget the way the picture shows it piped I'm interested in how it's piped as standard so oil from the tank to the pump inlet out of pump back up to sight glass in tank out of sight glass to 2 wat tap one way to engine the other to gearbox but with this timing side connection does the 2 way oil valve connection that feeds the gearbox on most model 9's have to be disconnected and re-routed to this Timing chest side case feed connection? anyone know how it's piped up ......also what should the crank end float be.....0.005" ?......and one last question the brass inserts that take the tappet adjuster sliders how do they come out are the an interference fit where they'll need to be heated and pulled out like teeth........your advice and pictures would be much appreciated thanks in advance