The Marston Sunbeam Club & Register Forum

General Category => Technical Discussion Forum => Topic started by: Fellwalker on November 06, 2026, 06:40:26 AM

Title: White smoke from exhaust from burning oil
Post by: Fellwalker on November 06, 2026, 06:40:26 AM
My 1936 Model 8 has started polluting the environment with lots of white smoke from the exhaust from burning oil.  We're going to take the head off and have a look, but other than valve guides and piston rings, are there any other potential causes we should look for?
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 06, 2026, 08:16:51 AM
I would start with the easy part and look for wet sumping (although I wonder why it should suddenly appear). Check the ball valve at the crankcase.
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 06, 2026, 05:17:52 PM
Thanks Thomas, unfortunately it appears the scraper ring is very tight upon the groove and a small gouge has been inflicted in the bore.  The piston is +60 thou.  I assume that's as big as they come?  Are there other pistons that could work and fit?  Has anyone looked at new cylinder liners?  Are barrels available?
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 07, 2026, 08:58:42 AM
Ok, an already affected piston/barrel is a reasonable cause for your problem. Aa far as I know a 60thou oversize piston is the maximum. A new standard one and a liner are in order. The latter is a simple task for any motor workshop as I've learned with my BSA (you don't need a new barrel). Pistons are a more delicate and lasting issue and our shop doesn't have it. I don't know alternative pistons but recently I've been at a specialized workshop (although in Germany): https://www.marston-sunbeam.org/sunbeamForum/index.php?topic=1356.0 That will be my silver bullet as soon as I need a new piston.
Cheers, Thomas
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 08, 2026, 07:24:18 PM
Thanks Thomas.  So, it's possible to fit a liner to this engine?  Also, would it be possible to overbore to +80 if the manufacturer you mentioned could make a piston of that size?  Is there enough material in the barrel on these old bikes?
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 08, 2026, 08:20:34 PM
I think a liner is possible for almost all engines. As far as I know this is also valid for your Model 8. But you should know the wall thickness. As you ask, it is essential to know how much material is there. I would call Klaus Wahl from Wahl-Spezialkolben or send an email. He will certainly help. Maybe you can measure by yourself. And he will probably be able to make any piston from a blank but I can't tell if +80 is a good idea because the piston-crank-balance might then be out of tolerance. At least, I never heard about 80+.
Cheers, Thomas
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 08, 2026, 09:01:06 PM
Thanks Thomas.  Yes, I assume there's a reason no one goes beyond +60.  I've messaged a local engine machining company and will see what advice they can give.  The ideal solution would be to liner that brings the bore back to standard so I can use a standard piston.  Let's see if it's possible.
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 12, 2026, 12:29:23 PM
Work is underway to fit a liner to the cylinder barrel and to try and source a piston (backstop is to use Wahl in Germany if needs be).

I assume there's no source for top end gaskets or for the rings that provide a degree of sealing at the top of the pushrod tubes?  How do people deal with these requirements?
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 12, 2026, 03:52:03 PM
There're no top end gaskets because the oil will drain from the rocker box via inside tube connections. However, there are two copper gaskets for each tube at the lower end. You can find it here on page 39: https://marston-sunbeam.org/1937-sunbeam-model-9-overhaul-part-2/
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 16, 2026, 08:01:33 AM
So, I think that what I have is a spacer at the top of the barrel and possibly at the top of the pushrod tubes.  When the guy at the company fitting the liner looked at the piston he noticed that it had been milled and I think it's possibly a Norton 50 or similar piston that's been milled down to fit.  The piston probably requires a spacer so that the crown doesn't contact the head.  See photos of the cylinder spacer and the spacers/o-rings on top of the pushrod tubes.

Any thoughts?
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 16, 2026, 08:36:01 AM
It sounds as if somebody tinkered unprofessionally. But I'm not sure about what you describe. Why a spacer between barrel and head if the piston is already milled at its top to fit? Anyway, instead of using a piston from another machine I recommend to let a matching piston made.
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 16, 2026, 12:22:31 PM
The piston was milled to reduce its diameter, not its height.  But is agree that getting an original made/found is the solution.  The problem now is, what is an original piston for my 1936 350?  Is there a spec somewhere as there's no point using my piston as the basis for a recreation.
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 16, 2026, 08:33:20 PM
As I wrote about Wahl: He has a number of documents and drawings for Model 9 pistons (I was looking for). Send him an email and ask if he has them for your Model 8.
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 17, 2026, 07:39:54 AM
Yes, I sent them an email and they replied very promptly, but they'd like me to send my piston so they can use it as a pattern.  Sadly, that's not going to work in this case.
Title: Re: White smoke from exhaust from burning oil
Post by: Thomas on November 17, 2026, 04:55:12 PM
Ok, was worth a try. I'm running out of ideas and only find a 350cc oversize piston from a B24: https://www.cornucopia-enterprises.de/sunbeam.html I have no idea if that piston would fit into a Model 8. Last idea: https://www.fwthornton.co.uk
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 17, 2026, 05:30:28 PM
Thanks Thomas.  I saw the B24 piston and equally have no idea whether it would fit.  I'll contact Thorntons.
Title: Re: White smoke from exhaust from burning oil
Post by: Fellwalker on November 22, 2026, 02:14:32 PM
Brief update:  I placed an order with F W Thornton on Friday to have a piston made in Australia.  I hope it's the right spec - the measurements appear correct but there's some concern that the 1930-35 pistons may be slightly different to the 1936 piston.  Whether the differences are significant (or as significant as replacing a Sunbeam piston with what may be a milled Norton piston in my engine) remains to be seen, but since I'm not trying to extract maximum performance from the Sunbeam, hopefully everything will work OK.  I'll provide an update once the barrel's been sleeved and the piston arrived, hopefully both before Christmas.