Fuel pipe Diameter

Started by Russ, January 11, 2023, 11:43:01 AM

Previous topic - Next topic

0 Members and 2 Guests are viewing this topic.

Peter 100

Russ
Cheers would never have thought to do that, makes sense.
Peter
1934 Sunbeam model 9 🏍️
1946 Austin 10 🚙

Russ

Quote from: Peter 100 on January 13, 2023, 03:28:45 PMNice job. How did you bend it without flattening, was it just a case of pulling it around a round former?
Peter

I had to hand a 2 1/4"" x 5/16" thick x 6" long piece of pipe....it's what I used to send home my main seals on my '66 T120TT.......anyway all I did was take a length of 1/4" pipe crimp one end and filled it with normal table salt giving it lots of taps to compact the salt....that was the difficult part....LOL....then when it was full I crimped the other end off....then I bent a single 90 degree bend allowing me to clamp lightly the pipe and the former pipe in the vice....I picked a start for the coil somewhere near the middle making sure I left enough tail end to cut back for the final connections.....the trick is to be smooth and continuous in wrapping the pipe around the former.....on reflection I think 2 1/4" is a bit too big a diameter I mean it looks alright but I think 1 1/2" would be better

Peter 100

Nice job. How did you bend it without flattening, was it just a case of pulling it around a round former?
Peter
1934 Sunbeam model 9 🏍️
1946 Austin 10 🚙

Russ

ok chaps so I've curled a new fuel pipe in 1/4" I'll also do one in 5/16" then I'll have both still need to fit up with final bends for connection....end fittings to be silver soldered on later......thanks everyone

20230113_124640.jpg

Russ

Quote from: Peter 100 on January 11, 2023, 02:31:27 PMHi Russ
I have looked at my spares list dated 1932 and while it shows the pipes and part number it does not give the size.
My bike actual measurements are 5/16 for oil and 1/4 for fuel.
Cheers
Peter

thanks Peter

Quote from: Thomas on January 11, 2023, 02:41:52 PM1/2" for oil and 1/4" for fuel at my 1937 M9. Cheers, Thomas

thanks Thomas

Quote from: singleminded on January 11, 2023, 03:32:35 PM5/16" for oil and 1/4" for fuel on both mine. If you have thin wall 1/4" copper it can be a challenge to stop it collapsing . Screwfix copper pipe was no good for the oil lines , it wanted to bend in my bender rather than follow the former. I used refrigeration quality pipe,thicker walled.

I use Kunifer copper brake line tube (std 22swg) 90% Copper 10% nickel.....I've also used in the past 1m straight lengths of 1/4" and 5/16" 18swg (1.2mm thick wall) from model engineering suppliers Maccmodels but it's an absolute nightmare to bend you got to get seriously physical with it even having to apply heat while in the bending tool

singleminded

5/16" for oil and 1/4" for fuel on both mine. If you have thin wall 1/4" copper it can be a challenge to stop it collapsing . Screwfix copper pipe was no good for the oil lines , it wanted to bend in my bender rather than follow the former. I used refrigeration quality pipe,thicker walled.

Thomas

1/2" for oil and 1/4" for fuel at my 1937 M9. Cheers, Thomas
1946 BSA C11
1937 Sunbeam Model 9
... and a scratched Hyundai
(MSCR member)

Peter 100

Hi Russ
I have looked at my spares list dated 1932 and while it shows the pipes and part number it does not give the size.
My bike actual measurements are 5/16 for oil and 1/4 for fuel.
Cheers
Peter
1934 Sunbeam model 9 🏍️
1946 Austin 10 🚙

Russ

#1
I'm sure it doesn't matter too much but I've got to curl myself a new fuel pipe which should be an interesting exercise but which pipe diameter would be best 1/4" or 5/16" I have both pipe diameters on the shelf and the relevant fittings....I'm erring towards 5/16" as it will then be the same diameter as the oil pipes lines I've made.....what size would they have been.......cheers